Sir Tool P231
Arbor needed for the proper installation
of the balance shaft oil seal.
Applicable: Porsche model 944.

Sir Tool 1032T
36mm Open End
Long Thin Spanner Wrench
(8mm thickness) Spanner
Overall ength 20 inches.

Sir Tool 1036T
36mm Open End
Long Thin Spanner Wrench
(8mm thickness) Spanner
Overall ength 20 inches.

Sir Tool 9710
T.D.C. Indicator
Needed for T.D.C. on any gas engine.
Simply unscrew a spark plug and twist
the rubber hose part of this tool into the
spark plug hole. As you rotate the engine
with a turning bar, the piston forces air
through the whistle part of this tool.
Once the whistling stops the engine is at T.D.C.

Sir Tool 4491B
22mm Special Socket 3/8 Drive

Sir Tool ST0229
1/2 Drive Triple Square Drain Plug service tool
16mm XZN Heavy duty socket for Boxster.

Sir Tool 10-208
Valve Shim Pliers
Needed for the R&R
of valve adjusting shims. 
Applicable: Overhead Cam engines.

Sir Tool 10-218A
Valve Stem Seal Plier
Needed for the proper extraction of stem seals.
The inside grooves on the tips of this plier
allows the firm grip of both O.E. and aftermarket seals
Applicable: Overhead Cam engines.

Sir Tool 1032X36T
Thin Spanner Wrench 32 X36mm with
an 8mm overall thickness
and a length of 12inches.
The 32mm is needed for proper R&R
of tie rods Model 911 Turbo, 89 -76.
The 36mm is needed for proper adjustment
of rear ride height 911 , 89-77'

Sir Tool 4491A
22mm Special Tube Socket
1.)Used for securing the strut tower
retaining nut of most European models
(crucial when adjusting tension of front shocks).
The 2/3 open side walls of this socket allows for
easy access of an adjusting wrench.
2.) R&R of Oxygen Sensor.
3.) Used for R&R of Mercedes Deisel injectors.
OM604, 605 & 606

Sir Tool P234
Oil Seal Arbor needed for the proper installation
of oil seal on flywheel side of crankshaft.
Applicable: Porsche model 911 ‘78-’94, 928, 944, 968.

Sir Tool 1089
Designed to extract bearings and bushings
with an I.D of 15mm and up to 20mm
For Bearing use only!
Not Bushings. Applicable: Most Models

Sir Tool VA6010
Valve Spring Compressor Bar
Needed for R&R of valve spring or rocker arm
With this tool the job can be done
with the cylinder head on or off the car.
Used in conjunction with tool VA6022. 
Applicable:Model 924. VW AUDI 4-5 Cylinder 

Sir Tool VA 6022
Support Bridge
Needed for R&R of valve spring or rocker arm
Used in conjunction with tool VA6010.
Applicable: Model 924. VW / AUDI 4 - 5 Cylinder 

Sir Tool P 215
needed for the proper installation
of oil seal on flywheel side of crankshaft. 
Applicable: Porsche model - 911 ‘65-’77.

Sir Tool 1018
Pressure Adaptor needed for pressuring the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Comes with a 1/4-18 NPT threaded opening.
Applicable: Most every European model. 

Sir Tool 1045
Drift needed for removing disc brake pads.
This Drift is designed to press the brake pad
retaining pins back w/o damage to pin or caliper.
Applicable: Porsche models.
Also, for a variety of other applications.

Sir Tool 1017
1/2 Dr.Heavy duty Allen socket
designed specially for R&R of
gearbox drain plugs.
Also for a variety of other applications.
AppL: Most European Vehicles.

Sir Tool P226
Synchro Engagement Kit
needed for the proper removal of synchro rings
from the gear.
Applicable: Porsche  911 ‘72-’86 1st, 2nd gears.

Sir Tool P225
Synchro Engagement Kit
needed for the proper removal of synchro rings
from the gear. Applicable:
Porsche model - 911 ‘72-’86  3rd, 4th, 5th gears;
912 ‘65-’71 all gears; 914 all gears.

Sir Tool P 224
Synchro Engagement Kit
needed for the proper removal of
synchro rings from the gear.
Applicable: Porsche model 911 Turbo
w/4speed ‘76-’88 1st, 2nd gears.

Sir Tool P 223
Synchro Engagement Kit
needed for the proper removal of
synchro rings from the gear.
Applicable: Porsche model 911 Turbo
w/4speed 76-88 3rd, 4th gears.

Sir Tool P 221
Eccentric Adjuster
needed for Toe-In of rear suspension.
Applicable: Porsche model  911, 924, 944.

Sir Tool P 216
Oil Seal Arbor needed for the
proper installation of oil seal
on pulley side of crank shaft.
Applicable: Porsche model - 911 ‘65-89.

Sir Tool P 235
Extremely crucial when adjusting
camber of front wheels.
Applicable: Porsche model - 911 C2 & C4.

Sir Tool 1014
Separator needed for disassembly
of pitman arm type tie rod ends
without tearing the ball joint boots.
Applicable: Late Porsche models.

Sir Tool P 213
Feeler Gauge Holder and one blade (.004")
needed for correct adjustment of valve clearance.
Comes exclusively as shown here with its correct shape
for the contour of your hand.
Applicable: Porsche 356, 911, 912, 914-6, 930.

Sir Tool P 213-B
5 pack replacement feeler gauge blades,
.004" thick. Used in conjuction with P213 Holder.
Applicable: Porsche model - 911.