Sir Tool P201-313-215
Professional Engine Holder Complete Kit
Includes Tool Numbers:P201, 313 and 215.

Sir Tool 313
Heavy Duty Bench Clamp 
Designed to securely carry
the full weight of an air-cooled
twin turbo Boxer -6.
Properly suited for a work bench.

Sir Tool P201
Holder used in conjunction with
Heavy Duty Clamp 313 which allows
for a full 360 degree rotation
of motor, and Flywheel Lock 215
allowing for R&R of motor.

Sir Tool 215 Flywheel Lock used to secure
the crank shaft from rotating
during R&R of motor.
Used in conjunction with
Engine Holding Fixture P201
where Flywheel Lock bolts
into a machined channel.
6V or 12V  Air-cooled motors.

Sir Tool VA6019
Valve Stem Installer
(8mm) Needed for proper installation of Valve Stem
Applicable: Model 924. VW-AUDI 4-5 Cylinder 2.

Sir Tool P241
Spring Clips (Pair), P241 needed for
securing cam followers within crank case half
during assembly.
Applicable: Porsche 356, 912, 914.
Every VW air-cooled engine.

Sir Tool P232
Locking Bar needed to properly secure the balance shaft sprocket from rotating during R&R of retaining bolt.
Applicable: Porsche model - 944.

Sir Tool P218
Alignment Pin crucial in order to
properly reinstall the oil filter/water intercooler housing.
Not using this Alignment Pin may cause
misalignment during this procedure,
which may lead to the oil pressure
relief valve sticking and ultimately engine damage.
Applicable: Porsche model - 944 ‘83-’86.

Sir Tool P242
Spanner Wrench Set
needed for R&Rb of oil lines.
This 4-pack set includes:
(1) each of the following wrench sizes:
27mm, 30mm, 32mm, 36mm.
Applicable: Porsche 911, 930, 914-6, 944, 968.

Sir Tool P212
Oil Seal Arbor Needed for proper
installation of oil seal on flywheel side
of crank shaft.
All Porsche VW Boxer 4 (Excluding 914)

Sir Tool P240
Dial Gauge Holder
needed to properly
measure crank shaft flywheel
and pulley end-play.
Can also be universally to check clearances
and run-out. Applicable: Most every
Porsche and VW air-cooled engine.

Sir Tool P236
Oil Piston Pressure Relief Valve Puller
needed for the proper extraction of
the oil piston pressure relief valve
from engine case.
Applicable: Porsche 356, 912, 914.
All VW air-cooled engines.

Sir Tool P229
Distributor Drive Gear Puller
needed for the proper extraction
of the distributor drive gear from
engine case. Applicable: Porsche model 356, 912, 914. All VW air-cooled engines.

Sir Tool P239
Starter Bushing Puller - 12V
Applicable: All Porsche and VW Boxer-4
12V models.

Sir Tool P238
Starter Bushing Puller - 6V
Applicable: All Porsche and VW Boxer-4
6V models.

Sir Tool P207
Dial Gauge Holder (Z Block), needed for accurate adjustment of valves. Made from high grade aluminum with an anodize finish. Comes equipped with a 50mm dial indicator extension pin.
Applicable: Porsche model - 911, 930.

Sir Tool P217
Rivet Driver needed to properly secure spring clips onto the rim which holds the hubcap on the wheel. Applicable: Correct wheel setup for all Porsche 356 models with drum brakes and VW ’67 and older.

Sir Tool P233
Flywheel Lock needed to stop the motor from rotating during R&R of crank shaft bolt or motor. Applicable: Porsche model - 944.

Sir Tool P228
Spring Loaded Gauge
displays valve spring height using
pre-calibrated indicators stamped onto
the outside surface of this tool.
Crucial for accurate valve spring adjustment.
Applicable: Porsche model - 911.

Sir Tool P243
8mm Extra Long Allen Socket
Solid one piece construction needed for busting loose rusted bolts of heat exchangers/exhaust systems.
The extra long length easily accesses these hard to reach exhaust system bolts. 3/8" drive. 
Applicable: Porsche model 911, 930.

Sir Tool P222
17mm Magnetic Box V-Wrench
needed for securing the top engine bolts
from rotating during R&R
of motor from transmission.
Applicable: Porsche, VW and Ferrari
models using 17mm connecting bolts
with a Hex Head.

Sir Tool P210
Ball Joint Pin Wrench Socket 
Socket with 1/2" drive and a pin reinforcement sleeve, needed for the proper R&R of ball joint nuts w/o damage to the Pin Wrench Socket or nut. Applicable: Porsche model - 911 ‘65-’89, 912, 914.